Repository logo

Infoscience

  • English
  • French
Log In
Logo EPFL, École polytechnique fédérale de Lausanne

Infoscience

  • English
  • French
Log In
  1. Home
  2. Academic and Research Output
  3. EPFL thesis
  4. Multilayer diffusion-barrier composites based on microfibrillated cellulose from wood, bacterial and algae sources
 
doctoral thesis

Multilayer diffusion-barrier composites based on microfibrillated cellulose from wood, bacterial and algae sources

Schreier, Aigoul  
2024

This work is driven by the effort towards increased environmental sustainability and aims to develop a new food packaging material based on renewable materials, and more specifically cellulose as the most abundant biomass resource on Earth. Focus was on microfibrillated cellulose (MFC) known for its exceptional diffusion barrier performance at low relative humidity, which however rapidly degrades with increasing humidity, and on strategies to reduce this sensitivity to moisture. The first objective was to investigate alternative MFC from algae and bacteria. A commercially available wood-MFC was selected as a benchmark. The algae-MFC was extracted from Boergesenia forbesii algae. The bacterial cellulose (BC) was produced via fermentation of Komagataeibacter xylinus bacteria in two variations: a standard BC-Control and BC-Cremodan, cultivated in a foamed medium with cremodan and xanthan. Aqueous suspensions of MFCs were shear-thinning and exhibited a yield stress with increasing concentration. The BC-Cremodan and algae-MFC suspensions with high nanosized fractions and fewer physically entangled agglomerates were less stiff than the BC-Control and wood-MFC suspensions with rougher and longer macro-fibers. The analysis of self-standing nanopapers produced with these MFC revealed the complex interplay between microstructural factors such as crystallinity, nanofraction and residual water content and macroscopic properties, as the Young's modulus and the water vapor permeability. The oxygen transmission rate (OTR) of the MFC films at high humidity was comparable to the values of conventional packaging materials such as PET and their water vapor transmission rate (WVTR) was an order of magnitude higher than that of PET, but an order of magnitude lower than values for previous MFC films. The second objective was to suppress the considerable sensitivity of MFC to moisture, and more specifically to maintain its very high barrier against the diffusion of oxygen at high relative humidity. The approach was to encapsulate the MFC films with hydrophobic polymers in the form of multilayer coatings on a paper substrate. Two different types of polymers, namely photo-curable organic-inorganic epoxy-based formulations, and an acid-modified polyolefin suspension (PO) were selected. The epoxy hybrid approach improved the OTR and WVTR of the MFC by an order of magnitude, and the addition of a sol-gel inorganic network into the epoxy network was instrumental to achieve a high mechanical integrity, with no delamination at the polymer-MFC interface. The PO approach was tested with the wood-MFC and algae-MFC and enabled to largely decrease the WVTR of the MFC, both at 50%RH and 85%RH, with a marginal effect on the OTR. The algae-MFC with an open porosity led to a high adhesion with cohesive failure within the MFC layer owing to a mechanical interlocking effect with the PO layers. The phenomenon of water transport within the MFC/epoxy hybrid and MFC/PO multilayers was further explored using transient and steady-state permeation approaches. This analysis confirmed the absence of a strong synergy within the multilayer architectures with a limited encapsulation effect. The assumption of a Fickian diffusion moreover led to artefacts in the derivation of the diffusion and solubility coefficients for water. This was considered to reflect a diffusion-reaction type transport, where water molecules absorb on active sites at the interfaces and within the MFC network.

  • Files
  • Details
  • Metrics
Type
doctoral thesis
DOI
10.5075/epfl-thesis-10745
Author(s)
Schreier, Aigoul  

EPFL

Advisors
Leterrier, Yves  
Jury

professeure Cécile Hébert (présidente) ; Dr Yves Leterrier (directeur de thèse) ; Prof. Tiffany Abitbol, Dr Violette Bourg, Dr Gilberto De Freitas Siqueira (rapporteurs)

Date Issued

2024

Publisher

EPFL

Publisher place

Lausanne

Public defense year

2024-06-14

Thesis number

10745

Total of pages

143

Subjects

Microfibrillated cellulose

•

Bacterial cellulose

•

Algal cellulose

•

Barrier coatings

•

Multilayer coatings

•

Packaging

EPFL units
LPAC  
Faculty
STI  
School
IMX  
Doctoral School
EDMX  
Available on Infoscience
June 4, 2024
Use this identifier to reference this record
https://infoscience.epfl.ch/handle/20.500.14299/208227
Logo EPFL, École polytechnique fédérale de Lausanne
  • Contact
  • infoscience@epfl.ch

  • Follow us on Facebook
  • Follow us on Instagram
  • Follow us on LinkedIn
  • Follow us on X
  • Follow us on Youtube
AccessibilityLegal noticePrivacy policyCookie settingsEnd User AgreementGet helpFeedback

Infoscience is a service managed and provided by the Library and IT Services of EPFL. © EPFL, tous droits réservés