Semiconductor nanowires are an emerging class of materials with great potential for applications in future electronic devices. The small footprint and the large charge-carrier mobilities of nanowires make them potentially useful for applications with high-integration density, but also to replace thin-film transistors in large-area electronics. This thesis investigates the use of wet-chemically grown ZnO nanowires for the fabrication of high-performance, low-voltage field-effect transistors (FETs). The first part of this thesis addresses the electrical characteristics of the wet-chemically grown ZnO nanowires. The as-grown ZnO nanowires are highly conductive due to a large charge-carrier concentration caused by dopants unintentionally incorporated into the ZnO nanowires during the synthesis. This large charge-carrier concentration makes it difficult to modulate the conductivity of the nanowires by an external electric field, so that the as-grown wires are not suitable for FETs. A post-growth annealing step is employed to dramatically reduce the charge-carrier concentration of the nanowires which makes it possible to fabricate FETs with useful characteristics. ZnO-nanowire FETs in a global back-gate geometry based on annealed ZnO nanowires have a transconductance of 300 nS, an on/off current ratio of 107 and a subthrehold slope of 500 mV/decade. The maximum field-effect mobility of the annealed ZnO nanowires is around 50 cm2/Vs. An important requirement to obtain good FET characterisitcs is to minimize the influence of the source and drain contact resistance on the total device resistance. The material used for the source and drain contacts in this thesis is aluminum. It is demonstrated that the use of a plasma treatment in the contact regions prior to the evaporation of the aluminum contacts can greatly influence the contact properties between ZnO and aluminum. An argon-plasma treatment locally increases the charge-carrier concentration in the ZnO. It is shown that the doping effect of the argon-plasma treatment can be exploited to reduce the contact resistance between alumiunm and ZnO and improve the electrical performance of the FETs. In the second part of this thesis, the influence of the ambient air on the electrical characteristics of the ZnO-nanowire FETs is investigated. The electrical conductivity of the FETs is strongly affected by the distinct atmospheric conditions, which makes it difficult to obtain reliable FET characteristics. The potential of a self-assembled monolayer (SAM) based on fluoroalkylphosphonic acid molecules to passivate the ZnO nanowires against the undesirable effects of the ambient and to stabilize the electrical performance of ZnO-nanowire FETs is demonstrated. The stabilizing effect is attributed to the formation of a densely packed, hydrophobic SAM on the surface of ZnO and aluminum oxide. The quality of the hydrophobic SAMs is confirmed by means of water-contact-angle measurements on SAM-covered ZnO single crystals that show a contact angle of more than 110°. The third part of this thesis is dedicated to the fabrication of high-performance ZnO-nanowire FETs with patterned metal top-gate electrodes. A top-gate fabrication process is developed that uses a very thin gate dielectric consisting only of an alkylphosphonic acid SAM that can be deposited from solution. The insulating quality of the SAM is investigated for top-gate FETs that utilize either gold or aluminum for the top-gate electrode. Gold top-gate FETs show a transconductance of 1 µS, an on/off current ratio of 107, and a steep subthreshold slope of 90 mV/decade. The thin gate dielectric makes it possible to operate the gold top-gate FETs at low voltages of 1 V and simultaneously reduces the undesired gate current by more than three orders of magnitude compared to gold top-gate FETs that have been fabricated without a gate dielectric (MESFETs). The gate current of the gold top-gate FETs with SAM gate dielectric is as low as 1 pA for gate-source voltages between -1 V and 0.5 V. When aluminum is used for the top-gate electrode, a hybrid dielectric is formed at the interface between the SAM and the aluminum, consisting of the SAM and a spontaneously formed aluminum oxide layer. Owing to the hybrid gate dielectric, the aluminum top-gate FETs are operated with gate currents below 1 pA for voltages up to 3 V. The top-gate fabrication process does not require temperatures above 160 °C, which makes it possible to fabricate FETs on unconventional substrates that cannot tolerate high temperatures, such as glass or flexible plastics. Integrated circuits on single ZnO nanowires that are fabricated on glass and plastic substrates are demonstrated. The maximum switching frequency of the inverters is 1 MHz.